8 Techniques to Fix Badly Damaged Furniture

When I renovated this house I knew I wanted to have some painted dressers in the bedroom. Dressers are always best if you can find them second-hand, hand-me-downs or free on the side of the road. Why? Because they are usually solid wood and it’s very rare to find solid wood dressers anymore. Most new dressers, even expensive ones, usually have some form of MDF or veneer parts to it, usually the backs or drawers.

Every time I finish a dresser, there’s always something new to fix on it that I haven’t done on the last dresser. I’ve learned a ton along the way through trial and error and I’m sharing those tips with you today.

So you can have a stunning piece of furniture in your house for almost nothing but time and sweat and maybe a few tears. Okay, it really isn’t that bad, but if you are willing to be patient with a piece of furniture, it can be done.

HERE ARE 8 TECHNIQUES ON HOW TO FIX BADLY DAMAGED FURNITURE.

The first photo above shows the after of this bad dresser. It really was in bad condition but I have seen worse (wait until you get to the bottom of my post!).

1. WHAT TO DO WHEN VENEER IS COMING OFF:

This dresser didn’t look like this when I bought it. There was some small flaking on the one side and when I touched it, it easily lifted off. So instead of puttying it down, I just lifted off all the loose bits.

Yikes.

Now what? You putty like mad. Buy yourself a few tubs of wood putty and give yourself a couple of days. Apply the mud with a putty knife, let it dry and sand it (I used a hand sander for this job). You’ll repeat this process over and over until you achieve a nice smooth finish.

You may need to repeat this step by adding wood putty, letting dry and sanding down a couple of times depending on how bad the repair is.

Wood putty works like magic and will still stand up to wear and tear. So don’t be afraid to use it! It’s your best friend in furniture repair when you are going to paint it after.

2. WHAT TO DO WITH CRACKS AND HOLES:

You’ll come across all sorts of little cracks and holes and it will be difficult to get your putty knife into. Just dab your finger into the mud and push it into the cracks.

Using a sanding sponge after its dried will be easiest to get a smooth finish.

For larger cracks, use wood glue and hold together with clamps for 24 hours.

3. WHAT TO DO WHEN THE HARDWARE IS MISSING:

There was one handle missing on this dresser (of course, just one!) and I had some leftover knobs from the vintage pink dresser so I added two similar knobs to just the top drawer.

You can find vintage knobs at thrift stores or antique stores or new knobs that look old at places like Anthropologie.

Use wood putty again to cover up these holes and sand after drying until you have a smooth finish. You may need to repeat this step two to three times to get a smooth finish. Then drill a new hole in the centre for the single knob.

4. WHAT TO DO WHEN THE INNER DRAWER GUIDES HAVE FALLEN OFF:

Drawer guides are a two-part mechanism. One part stays on the bottom of the drawer and the other part is attached inside the dresser guiding in the drawer.

When the inner drawer guide is loose, the drawer won’t guide in straight and sit flush . so annoying).

Using Gorilla Glue, dab the parts that are loose and clamp into place and let dry for 24 hours. Put a rag or paper towel underneath as the glue will ooze before it completely dries.

5. WHAT TO DO WHEN THERE ARE MISSING DRAWER GUIDES:

For this dresser, there were two missing drawer guides on the bottom of some drawers. New drawer guides are plastic and won’t fit to old wood furniture so I came up with this easy solution!

I took some existing drawer guides from the same dresser that were nearly falling off anyway and cut them in half with a jigsaw. I attached the cut guides with an adhesive silicone and glued it to the back part of each drawer. I sat bricks on them overnight to secure into place.

Half or a portion of a guide is all you need to guide the drawer in on the rail and the drawer will still align up flush.

6. WHAT TO DO WHEN THE FINISH IS BAD:

You paint it of course!  Champlain for the main color and Putty for the interior and exterior of the drawers.

I finished it off with the clear furniture wax and buffed it off to a smooth finish.

7. WHAT TO DO WITH OLD HARDWARE:

The hardware belonging to an old dresser can be so worn that the original finish has worn off or it can be too brassy looking. I used Rub N Buff in European Gold finish to give it that matte gold finish.

You just dab some on a cloth and rub it in. That’s it. This stuff is pretty amazing. You can also rub it off if it’s too much or if you want a distressed look. It goes on like a wax or furniture polish.

8. WHAT TO DO IF THE WHOLE PIECE HAS FALLEN APART:

Do you remember that piece of furniture that had completely fallen apart and was on its way to the dump when I decided to resuscitate it?

I decided that large amounts of wood putty and finishing nails would do the trick and it did!

The small top drawers were completely broken so I opted for an open shelf there instead.

You can see all the putty everywhere and I added a new piece of wood to the inner top shelf that was once two little drawers.

There were only three feet so I took the existing feet off and it just sat flush on the ground. 

Tons of puttying, sanding, nailing, painting and it’s now rescued!

So here is the finished dresser that I started this post with. I love before and afters, don’t you?

It makes all the hard work worthwhile. I’m in love with this dresser now and you’d never know it had so many problems.

 

 

 

 

 

 

 

 

This blog post was created and originally posted by:

 


Leave a comment

Please note, comments must be approved before they are published